Skip to content
Open access

Dynamic and Post-Deformation Static Aging as an Integrated Approach to Thermomechanical Processing of TiNi Shape Memory Alloys

Aug 2026 · Journal of Manufacturing and Materials Processing · Vol 10, pp. 278 · 0 citations · 38 references

Abstract

The effect of thermomechanical processing (TMP) parameters on the structural-phase evolution and properties of Ni-enriched Ti–50.8 at.% Ni shape memory alloy was investigated. Compression deformation was performed at T = 300–500 °C, accompanied by the development of dynamic aging (DA) processes, to true strains of e = 0.5–1.3, followed by post-deformation static aging (SA) at 430 °C for 1 and 10 h. The structural-phase state and properties were characterized using optical and transmission electron microscopy, X-ray diffraction, differential scanning calorimetry, and Vickers hardness measurements. The results confirmed that DA processes were activated during compression but proved insufficient for pronounced Ti3Ni4 precipitate growth compared with SA. The temperature range of 430–500 °C promoted the most intensive DA processes and facilitated ultrafine-grained structure formation. The processing route combining DA at 500 °C with short-term SA (1 h) resulted in the finest precipitates of Ti3Ni4 phase and most homogeneous substructure. These findings demonstrate that the proposed TMP strategy enables effective tailoring of precipitate dispersion, evolution of transformation temperatures and mechanical properties (hardness), providing a viable manufacturing pathway for tailoring TiNi SMA performance in advanced biomedical and engineering applications.

Read PDF

Similar papers

Open access Sep 2026

Effect of Temperature and Strain Rate on the Thermomechanical Response and Dynamic Restoration Mechanisms of Ti-6Al-4V Alloy During Forging

The thermomechanical behavior of the Ti-6Al-4V (Ti64) alloy under hot deformation is determined by a complex interplay between strain hardening and thermally assisted restoration processes that finally lead to the formation of the resultant microstructure and mechanical properties. In this research, the effects of defo...

Shanli Salahi, Tolga Yılmaz, Onur Fevzi Kevenlik et al. · 0 citations
Open access Sep 2026

Aging-Induced Microstructural Evolution and Fracture Mechanisms of 35Cr45NiNb Alloy Under High-Temperature Tensile Deformation

Centrifugally cast 35Cr45NiNb alloy has been widely employed in ethylene-cracking furnace tubes owing to its excellent carburization and creep resistance. However, the influence of microstructural degradation and temperature on its high-temperature tensile behavior remains poorly investigated. In this study, an acceler...

Mo-Lin Su, Gang Yu, Zhi-Jie Gao et al. · 0 citations
Open access Sep 2026

Microstructure and Mechanical Response of Commercially Pure Titanium VT1-0 After Short-Term Hot Deformation

Short-term (1–2 s) hot bulk plastic deformation of commercially pure titanium VT1-0 was studied at 25, 500, 600 and 700 °C without post-deformation annealing. Optical metallography, XRD line-profile analysis and Vickers micro-hardness testing were used to characterize the as-deformed structural state. The α-Ti single-p...

A. Mamaeva, Talshyn Yetish, A. Panichkin et al. · 0 citations
Open access Oct 2026

Post-aging-induced microstructural, mechanical, and ductile fracture characteristics of 6082-T6 aluminum alloy

In this study, the effects of post-aging conditions on the mechanical properties, deformation behavior, and fracture characteristics of 6082-T6 aluminum alloy sheets were investigated, using tensile testing supported by DIC. Post-aging treatments were performed at 100 °C, 200 °C, 300 °C, and 400 °C, with holding times...

Mehmet Okan Kabakçı, O. Çavuşoğlu, O. Sahin et al. · 0 citations

We use cookies to run the site and, with your consent, for analytics and to show ads. See our Cookie Policy.