Skip to content

Eco-design of PLA/CNC nanocomposites with a dynamic-crosslinking network: enhanced nanofiller dispersion, strain hardening and mechanical properties via reactive extrusion.

Sep 2026 · Soft Matter · 0 citations · 49 references
Medicine

Abstract

In this study, a novel concept termed "polyol coating/crosslinked" was introduced for the PLA nanocomposites with a dynamic-crosslinking network (DCN) via a two-step reactive extrusion process. In this approach, polyols were used both as crosslinking components and physically coating agents of cellulose nanocrystals (CNC) and through a freeze-drying method with water, CNC dispersion inside PLA was enhanced. Meanwhile, during the establishment of DCN inside PLA, the coated CNC were subsequently connected to the DCN to enhance reinforcement. The freeze-dried, glycerol-coated CNC exhibited significantly improved dispersion, indicated via an average distributed length of approximately 400 nm, which is much smaller than the several-micrometer length of untreated CNC particles. This enhanced dispersion and reinforcement further notably reinforced melt strength, mechanical stiffness and thermal resistance of the PLA/CNC composites. Much more pronounced strain hardening behavior, a ∼20% increase in storage modulus and 3.7 °C increase in Vicat softening temperature were observed compared with the neat PLA matrix. As a practical outcome, the CNC-reinforced DCN systems demonstrated excellent foamability, achieving a 25-fold foam expansion, attributed to CNC's role as a foaming nucleating agent. Last but not least, the entire process is recyclable, re-processable, organic-solvent-free and suitable for continuous melt extrusion. Based on these results, this method could potentially be applied to transform similar polyester-based polymer wastes into a composite DCN form, offering improved mechanical and melt-strengthening properties, without sacrificing the original processability, thus realizing upcycling of polyesters.

View source

Similar papers

Open access Sep 2026

Simultaneous Compatibilization and Toughening of Renewable PLA/PA11 Blend via Core-Shell Biobased Nanosilica-Filled Elastomer

Poly(lactic acid) (PLA) composites are attractive candidates for sustainable applications. However, achieving an optimal balance between toughness and heat resistance without sacrificing biobased content remains a persistent challenge. Herein, we develop PLA composites exhibiting concurrently high stiffness, toughnes...

Zhen-Feng Wang, Zi-He Zhao, Yu Cheng et al. · 0 citations
Conference Sep 2026

Reinforcement mechanism of KH550-modified cellulose nanofibers in continuous carbon fiber/polyamide 12 composites: a molecular dynamics simulation study

The mechanical properties of continuous carbon fiber (CCF) reinforced polyamide 12 (PA12) composites are typically governed by the weak polymer matrix and poor fiber-matrix interface. Both limitations can be alleviated by incorporating the KH550-modified cellulose nanofibers (CNF), yet, the underlying mechanisms requir...

Yu Wang, Xiao-Qi Chen, Ze Chai et al. · 0 citations
Open access Sep 2026

PEG‐Mediated Aqueous Processing of Cellulose Nanofiber/Polycaprolactone Composites

This study aimed to develop and characterize Cellulose Nanofiber/Polycaprolactone (CNF/PCL) composites using a low‐temperature, organic‐solvent‐free aqueous processing method. The composites were prepared by gradually incorporating a hydrated CNF/PEG gel into PCL melted at 75°C through repeated rolling and folding. FTI...

S. Anitasari, Niloofar Fani, Wen-Zhe Li et al. · 0 citations
Sep 2026

Epoxy chain extender compatibilized poly(lactic acid)/polyoxymethylene blends: Improved crystallization, enhanced heat resistance and toughness for three-dimensional printing.

Bio-based and biodegradable poly(lactic acid) (PLA) is severely limited in three-dimensional (3D) printing due to its inherent brittleness, poor heat resistance, and slow crystallization rate. In this study, PLA/polyoxymethylene (POM) composites were prepared via one-step melt blending with an epoxy-functionalized olig...

Jun Shen, Ran-Ran Si, X. Bing et al. · 0 citations
Open access Sep 2026

Ultra-High-Expansion-Ratio Nanocellular Semicrystalline Polymer Foams: Preparation of Chain-Extender-Mediated PLA/PPC Foams via Supercritical CO2

The inherent brittleness, retarded crystallization kinetics and insufficient melt strength of polylactic acid (PLA) severely limit its applications in foaming. This study proposed a reactive chain extender and compatibilizer strategy, which involved introducing the multifunctional epoxy-based chain extender KL-E4370 (0...

Xu-Bo Zhao, Xue-Jun Liu, Feng Hu et al. · 0 citations

We use cookies to run the site and, with your consent, for analytics and to show ads. See our Cookie Policy.