Skip to content
Open access

Design, Modeling, and Experimental Validation of a Novel Flexible-Joint Robotic Manipulator using Adaptive Sliding Mode Control

Nov 2026 · Revista Cultura Científica · Vol 2026, pp. 2296-2318 · 0 citations

Abstract

This paper presents the design, fabrication, nonlinear dynamic formulation, simulation, and experimental comparison of a robotic manipulator incorporating a four-spring flexible coupling. The platform is described as a four-degree-of-freedom (4-DOF) arm, and the supplied model distinguishes a motor-side coordinate from three load-side coordinates. Conventional sliding-mode control (SMC) and adaptive sliding-mode control (ASMC) are implemented through a LabVIEW real-time environment and a National Instruments myRIO controller. Reported tests consider no added payload, a 1000 g payload, and an external disturbance at reference angles of 45∘ and 135∘. The supplied simulation and experimental summaries are compared using position-error percentages, settling time, and maximum load torque. Across six matched experimental cases, ASMC reduces the reported position-error indicator by 40.4–50.0%, maximum load torque by 11.8–35.4%, and settling time by 4.6–6.3% relative to SMC. These reductions are calculated from the supplied table values and vary with operating condition and reference angle. The author-reported responses indicate recovery following the applied disturbances and less oscillatory behavior with ASMC. However, the available summaries do not quantify complete chattering suppression, statistical variability, or total actuator energy consumption. The adaptive implementation also introduces a smooth switching function, so the respective contributions of adaptation and smoothing are not isolated. The model structure and Lyapunov candidates are presented with explicit limits: the elastic torque law, numerical implementation details, actuator allocation, and complete closed-loop stability derivation require further specification. The comparison therefore supports the reported performance improvements for the investigated cases while identifying the information needed for full reproduction and broader validation.

Read PDF

Similar papers

Open access Sep 2026

Design and Simulation of a 4-DOF Robotic Manipulator with Real-Time Control and Path Planning

The integration of kinematics, dynamics, path planning, and GUI-based control demonstrates a comprehensive approach to robotic system development in a virtual environment, offering a flexible, low-cost, and scalable platform for research, education, and simulation-driven testing.

Rakesh M. D., Rajath S. R., R. B. · 0 citations
Open access Sep 2026

A Digital-Twin-Oriented Framework for Modeling, Control, and Virtual Validation of an Anthropomorphic Robotic Hand

This paper presents the design, mathematical modeling, control, and virtual validation of a fifteen-degree-of-freedom anthropomorphic robotic hand within a Digital Twin-oriented framework. The mechanical structure was designed in SolidWorks and integrated into MATLAB/Simscape Multibody to create a high-fidelity virtual...

C. Hernández-Santos, Amadeo Hernández, Arnoldo Fernández-Ramírez et al. · 0 citations
Open access Oct 2026

Modeling and Simulation Validation of a Lightweight Indigenous Six-Degrees-of-Freedom Robotic Manipulator (Dexter-6Pro)

The growing demand for inexpensive, locally produced robotic manipulators in developing nations has necessitated the development of efficient modeling and control techniques for both industry and research. This paper presents the modeling and simulation of Dexter-6Pro, a 6-DOF lightweight robotic manipulator developed...

Kinza Fatima, Hajra Qureshi, Muhammad Ahsan et al. · 0 citations
Open access Oct 2026

Learning-Based Adaptive Robust Control of a 4-DOF Robot Manipulator

This paper presents a learning-based adaptive control strategy for trajectory tracking of a four-degree-of-freedom (4-DOF) robot manipulator subject to unknown disturbances and model uncertainties. The designed controller combines nonlinear model-based compensation with online adaptation of the feedback gains and of a...

Mohammad Jafari, Dylan Cadigan, M. Reyhanoglu · 0 citations
Sep 2026

Modeling and analysis of a cable-driven manipulator based on computed torque control

Cable-driven manipulators have garnered increasing attention in robotics owing to their lightweight structure, flexible transmission mechanisms, and large operational workspace. However, the strong nonlinear dynamics, parameter coupling, and external disturbances inherent in cable-driven systems pose significant challe...

Jian-Hao Chai, Wei-Cai Quan, Xuan-Ming Tang et al. · 0 citations
Open access Sep 2026

Design and Redundancy Control Approach of a Novel Three-Platform Parallel-Coupled Mobile Robot

Based on the advantages of redundancy, high stiffness, and strong load-bearing capacity of parallel mechanisms, they can be applied in the field of mobile robots. This paper proposes a novel three-platform parallel-coupled mobile robot and conducts motion analysis and dynamic modeling for it. It proposes an active inte...

Wei-Wei Hu, Rui-Qin Li, Dian-Ying Lin · 0 citations

We use cookies to run the site and, with your consent, for analytics and to show ads. See our Cookie Policy.