Skip to content
Open access

Experimental Investigation of Constituent Materials for Multilayered Impact Resistant Panels: Fiber-Reinforced Ceramic, Shape Memory Alloy, and  Titanium Alloy Lattice Structures

Oct 2026 · Mehran University Research Journal of Engineering and Technology · Vol 45, pp. 138-147 · 0 citations

Abstract

This experimental study investigates the mechanical performance and energy absorption characteristics of materials for a newly developed multilayered impact-resistant panel. The proposed lightweight structure combines fiber-reinforced ceramic (FRC), nickel-titanium shape memory alloy (SMA), and additively manufactured Ti-6Al-4V lattice structures in uniform body-centered cubic (UBCC) and vertical-strut (UBCCz) configurations. Each material was fabricated, heat-treated under controlled conditions, and mechanically tested to assess its suitability for impact-resistant applications. The FRC panels exhibited a compressive strength of 50 MPa and a fracture toughness of 2.8 MPa·m¹ᐟ², supporting their use as a strike-face layer. Heat treatment of the SMA at 700 °C for 30 minutes increased energy absorption by 21% and failure strain by 40%, while reducing tensile strength. For both UBCC and UBCCz Ti-6Al-4V lattice structures, non-heat-treated samples demonstrated superior compressive properties compared with heat-treated samples. Increasing the UBCCz strut diameter from 1 mm to 2 mm substantially improved compressive strength and energy absorption. The experimental results for the multilayered panel were in good agreement with numerical simulation results reported in the literature. At an impact velocity of 100 m/s, the panel distributed the impact energy across its layers: 21% was absorbed by the FRC, 28% by the SMA, and 50% by the titanium lattice, while the aluminum backing contributed minimally. Multilayered impact-resistant panels with the same sequence of material layers were physically fabricated. Further impact testing is recommended to evaluate the panels’ damage and energy absorption behavior.

Read PDF

Similar papers

Open access Oct 2026

Steel-Wire Mesh Reinforcement of Topology-Optimized 3D-Printed ECC Beams: Experimental and Numerical Investigation

Engineered cementitious composites (ECC) exhibit tensile strain hardening and multiple cracking, providing an inherent self-reinforcing capability that endows ECC with suitability for the complex forms enabled by topology optimization and 3D printing. To extend such optimized structures to a broader range of engineerin...

Man-Fang Lin, Fan Yu, Zhen Yang et al. · 0 citations
Open access Oct 2026

Comparative Evaluation of Single and Hybrid Reinforcements in Aluminum Matrix Composites: Effects of SiC, Si3N4 and TiO2 Content on Mechanical and Tribological Properties

Aluminum matrix composites (AMCs) are attractive lightweight materials whose properties can be modified by the type and amount of ceramic reinforcement. In this study, Al–SiC composites containing 2 or 5 wt.% SiC were compared with hybrid Al–SiC–Si3N4 and Al–SiC–TiO2 composites containing 2 + 2 or 5 + 5 wt.% reinforcem...

A. Wąsik, B. Leszczyńska-Madej, M. Madej · 0 citations
Open access Oct 2026

Direct Tensile Behavior of Thermally Activated Concrete Reinforced with Short Iron-Based Shape Memory Alloy (Fe-SMA) Fibers: Experimental and Numerical Investigation

Short iron-based shape memory alloy (Fe-SMA) fibers can act as active internal reinforcement after thermal activation. This study examined the direct tensile behavior of concrete containing 2.0% by volume of straight Fe-SMA fibers, geometrically identical steel fibers, or no fibers. ASTM C307 briquettes were tested und...

Alireza Tabrizikahou · 0 citations
Open access Oct 2026

Experimental Investigation and Comparative Analysis of the Tensile and Flexural Properties of FDM 3D-Printed PLA and Carbon Fiber-Reinforced PLA Composites

Abstract: The Fused Deposition Modelling process parameters and thermal histories influence the structural performance of additive manufactured composites. The present work is an experimental investigation on flexural properties, interlaminar bonding, and mechanical load bearing capacity of Polylactic acid (PLA) compos...

Tushar Rahangdale, R. Thombare, Vicky Baelmare et al. · 0 citations
Jan 2027

Experimental Study on the Shear Behavior of T-Shaped Concrete Beams Strengthened with Bonded Straight Fe-SMA Plates Using Hybrid Anchorage

This study proposes a novel bonded straight iron-based shape memory alloy (Fe-SMA) plate system using hybrid anchorage for the shear strengthening of reinforced concrete (RC) T-beams and presents a comprehensive experimental evaluation of its structural performance. Unlike existing Fe-SMA shear-strengthening config...

Yu Sun, Zi-Qing Liu, Hong Zhu et al. · 0 citations

We use cookies to run the site and, with your consent, for analytics and to show ads. See our Cookie Policy.