Nov 2026· SAE technical paper series· Vol 1· 0 citations· 15 references
TL;DR
This work shows a scalable physics-informed neural-network framework that can be extended beyond battery systems to other components at system and vehicle levels and reduces dependency on computationally expensive simulations, thereby reducing development cycles and faster time for customers.
Abstract
Accurately predicting Thermal and Flow parameters in Battery Pack Thermal Management System is very important to ensure maximum system efficiency, long range and vehicle safety. Traditionally, conventional Computational Fluid Dynamics (CFD) methods are used to get detailed insights into these parameters. But these methods remain computationally very expensive, which limits their application in real-time predictions. This study presents an alternate structured simulation framework that combines CFD fundamentals with Physics-Informed Neural Networks (PINNs) to enable fast and efficient prediction of thermal and flow behavior. PINNs incorporates the governing partial differential equations (PDEs) - mass, momentum and energy – directly into the neural network's loss function, enabling efficient learning with limited dependency on training datasets.In this study, we present a PINN framework trained on limited datasets derived from general CFD simulations of flow and Conjugate Heat Transfer (CHT) cases for a battery pack. The trained PINN model is then validated against a separate set of test datasets obtained from independent studies, across key performance parameters including pressure drop, velocity, temperature distribution, and hotspot location. Comparative analysis indicates that the proposed PINN framework predicts key parameters within 5% deviation from test dataset values. The PINN model also significantly reduces computational time from 5-8 hours per case for traditional detailed CFD to 2-3 seconds. Additionally, the PINN framework requires only a closed-volume CAD geometry and does not rely on 3D-mesh. Limited data can be used to speed up the training process, thereby eliminating the time associated with pre-processing, repeated model setup for different cases, and subsequent corrections. Findings from this study demonstrate PINNs as a potential surrogate modelling tool for real-time thermal monitoring and rapid design iteration in battery cooling systems. This reduces dependency on computationally expensive simulations, thereby reducing development cycles and faster time for customers. This work shows a scalable physics-informed neural-network framework that can be extended beyond battery systems to other components at system and vehicle levels.
Steam methane reforming (SMR) is an important industrial reaction. Process simulation tools such as Aspen and computational fluid dynamics (CFD) are widely used to model it and perform well under specific operating conditions. However, when operating conditions vary and repeated calculations are required, the computati...
Hao Xin, Ming Xia, D. Murzin et al.· Processes· 0 citations
Accurate and rapid predictions of reactor transients such as Loss of Offsite Power (LOOP) events in Pressurized Water Reactors (PWRs) is critical for reactor safety assessment. Traditional highly benchmarked codes are computationally expensive, prohibiting their direct use in fast safety assessments. To address these...
Fabiano Thulu, Z. Wu, Yun-Fei Zhao· Frontiers in Energy Research· 0 citations
Accurate and reliable state of health (SOH) estimation is essential for lithium-ion battery safety and lifetime management. Physics-informed neural networks (PINNs) integrate battery degradation knowledge with deep learning to improve the physical consistency of SOH estimation. However, existing PINNs insufficiently ca...
Peng-Xiang Wang, Tao Wang, Xiao-Dong Xu et al.· Batteries· 0 citations
Transient conjugate heat transfer in coupled solid–fluid systems is governed by diffusion, advection, and heat transfer processes that can make repeated simulations expensive and time-consuming in the design phase. This study develops a physics-informed neural network for one-dimensional coupled solid–fluid heat transf...
A. Zappatore, Mauro Spró· Applied Sciences· 0 citations
Thermal design and monitoring of compact heat exchangers require fields across changing operating conditions, and increasingly from a few embedded sensors, yet each new Reynolds number is a new mesh-based simulation. A physics-informed neural network (PINN) framework is presented for the coupled prediction and inverse...
Gaston Haidak, Jian-Long Kou, Dong-Yun Wang· The Physics of Fluids· 0 citations
Proton Exchange Membrane (PEM) fuel cells are central to zero-emission transportation, but their power output is governed by coupled electrochemical and thermal dynamics difficult to predict for real-time control. Existing data-driven models either ignore the underlying electrochemistry or embed physics without validat...
Muhammad Own Raza, Muhammad Hanzla, Abdul Rahman Shinwari et al.· Discover Electronics· 0 citations
We use cookies to run the site and, with your consent, for analytics and to show ads.
See our Cookie Policy.