Skip to content
Open access

Shear-Induced Evolution of Cellular Structure and Thermo-Mechanical Properties in PLA/HNC and In-situ Fibrillated PLA/PTFE Composite Foams

Aug 2026 · Langmuir · Vol 42, pp. 25899 - 25911 · 0 citations · 44 references
Medicine

Abstract

High-performance cellular biopolymeric foams require precise control of processing and filler-induced microstructure. In this study, poly(lactic acid) (PLA) composite foams with halloysite nanoclay (HNC) and polytetrafluoroethylene (PTFE) were produced via twin-screw extrusion foaming using azodicarbonamide. The effect of screw speed (20–120 rpm) on morphology, crystallization, and compressive properties was investigated. In PLA/HNC, increasing screw speed improved filler dispersion and heterogeneous nucleation, reducing cell size by ∼50–60% and yielding a maximum void fraction of ∼20.5% at 60 rpm. In contrast, PLA/PTFE exhibited complete in situ fibrillation into a three-dimensional nanofibrillar network (∼100–500 nm), whose density increased continuously with screw speed without saturation. PLA/PTFE showed over a 20-fold reduction in crystallization half-time of PLA at 130 °C (vs ∼4-fold for HNC) due to its high nucleation surface area. It also achieved superior compressive performance (∼68–70 MPa·cm3/g strength and ∼11 J/g toughness at 120 rpm), exceeding PLA/HNC by ∼50% and ∼80%, respectively, through fibril-driven reinforcement mechanisms of cell walls.

Read PDF

Similar papers

Open access Sep 2026

Ultra-High-Expansion-Ratio Nanocellular Semicrystalline Polymer Foams: Preparation of Chain-Extender-Mediated PLA/PPC Foams via Supercritical CO2

The inherent brittleness, retarded crystallization kinetics and insufficient melt strength of polylactic acid (PLA) severely limit its applications in foaming. This study proposed a reactive chain extender and compatibilizer strategy, which involved introducing the multifunctional epoxy-based chain extender KL-E4370 (0...

Xu-Bo Zhao, Xue-Jun Liu, Feng Hu et al. · 0 citations
Open access Sep 2026

Nitrogen-Assisted Foam Injection Molding of Polylactide with Carbon Fibers and PTFE Nanofibrils

Polylactide (PLA)-based foams are viable sustainable alternatives to traditional petroleum-derived foams owing to their intrinsic biodegradability, superior biocompatibility, light weight, and high specific strength, with potential applications in packaging, insulation, and biomedical fields. However, their inherently...

Silla George Raju, Valentina Volpe, Rita Salomone et al. · 0 citations
Sep 2026

Epoxy chain extender compatibilized poly(lactic acid)/polyoxymethylene blends: Improved crystallization, enhanced heat resistance and toughness for three-dimensional printing.

Bio-based and biodegradable poly(lactic acid) (PLA) is severely limited in three-dimensional (3D) printing due to its inherent brittleness, poor heat resistance, and slow crystallization rate. In this study, PLA/polyoxymethylene (POM) composites were prepared via one-step melt blending with an epoxy-functionalized olig...

Jun Shen, Ran-Ran Si, X. Bing et al. · 0 citations
Sep 2026

Eco-design of PLA/CNC nanocomposites with a dynamic-crosslinking network: enhanced nanofiller dispersion, strain hardening and mechanical properties via reactive extrusion.

In this study, a novel concept termed "polyol coating/crosslinked" was introduced for the PLA nanocomposites with a dynamic-crosslinking network (DCN) via a two-step reactive extrusion process. In this approach, polyols were used both as crosslinking components and physically coating agents of cellulose nanocrystals (C...

Hu Qiao, Ji-Xiang Li, Bo Lu et al. · 0 citations
Open access Sep 2026

Simultaneous Compatibilization and Toughening of Renewable PLA/PA11 Blend via Core-Shell Biobased Nanosilica-Filled Elastomer

Poly(lactic acid) (PLA) composites are attractive candidates for sustainable applications. However, achieving an optimal balance between toughness and heat resistance without sacrificing biobased content remains a persistent challenge. Herein, we develop PLA composites exhibiting concurrently high stiffness, toughnes...

Zhen-Feng Wang, Zi-He Zhao, Yu Cheng et al. · 0 citations
Oct 2026

Interfacial Coupling Redirects Biaxial Deformation toward Diffusion-Suppressing Phase Reconstruction in Equimass Poly(3-hydroxybutyrate- co -4-hydroxybutyrate)/Poly(lactic acid) Blends

Combining poly(3-hydroxybutyrate-co-4-hydroxybutyrate) (P34HB) with poly(lactic acid) (PLA) offers a biodegradable route to balance deformability, stiffness, and optical clarity, but interfacial instability can compromise structural integrity during biaxial deformation. Here, a 50/50 P34HB/PLA blend was reactively co...

Xun-Da Hu, Hao-Miao Sun, Yun-Xuan Weng et al. · 0 citations

We use cookies to run the site and, with your consent, for analytics and to show ads. See our Cookie Policy.