Skip to content
Conference Open access

Towards Hybrid Soft-Rigid Robotic Manipulation: FEM and Experimental Characterization of Pneumatic Elastomeric Artificial Muscles for a Bioinspired Hand

Sep 2026 · International Conference on Electrical Engineering, Computing Science and Automatic Control · pp. 1-6 · 0 citations · 13 references

TL;DR

The obtained results demonstrate the feasibility of integrating pneumatic elastomeric actuators with rigid biomechanical structures while establishing a foundation for future compliant grasping and teleoperation applications.

Abstract

This paper presents the design, finite element analysis, fabrication, and preliminary experimental evaluation of a hybrid soft-rigid robotic manipulation system integrating pneumatic elastomeric artificial muscles with a bioinspired 3D-printed robotic hand. FEM simulations were implemented under internal pressures from 0.03 MPa to 0.09 MPa demonstrated progressive radial expansion accompanied by longitudinal contraction, achieving a maximum displacement of 11.05 mm and an 11% contraction at 0.09 MPa. A mesh convergence study confirmed the numerical stability of the FEM model using approximately 124,856 tetrahedral elements. The artificial muscle was fabricated using Dragon Skin 10 silicone elastomer reinforced with an external PET braided mesh, achieving a physical contraction close to 75 mm while supporting loads up to 2 kg. Additionally, a robotic hand fabricated through FDM 3D printing using PLA filament successfully reproduced flexion-extension movements in four fingers together with thumb mobility. The obtained results demonstrate the feasibility of integrating pneumatic elastomeric actuators with rigid biomechanical structures while establishing a foundation for future compliant grasping and teleoperation applications.

Read PDF

Similar papers

Open access Sep 2026

Design, Experimental Validation, and Pressure-Control Simulation of a Modular Pneumatic Soft-Finger Gripper

Pneumatic soft grippers adapt to uncertain object geometry through compliant deformation, and their performance is governed by chamber geometry, material behavior, pneumatic routing, and pressure control. This study develops a modular soft-finger gripper and a common-pressure-control platform. A toothed, multi-chamber...

Liang Wang, Ye-Ming Zhang, Mao-Lin Cai et al. · 0 citations
Open access Sep 2026

Morphology-Guided Nonlinear Structural Evaluation of a Hybrid Bio-Inspired Soft Robotic Actuator

Soft robotic actuators exploit structural compliance to produce adaptive motion, but their response depends strongly on the interaction between geometry, material distribution, specific reinforcement, and actuation. This manuscript presents a bio-inspired hybrid soft actuator based on the elongated, continuously deform...

E. Prada, Jaroslav Romančík, Peter Ján Sinčák et al. · 0 citations
Open access Oct 2026

Biomechanical Design, Additive Manufacturing, and Proof-of-Concept Evaluation of a 3D-Printed Transradial Prosthesis with a Manual Ratchet-Type Locking Mechanism

The manual ratchet mechanism provides an ultra-lightweight (344 g) and affordable (~$50 USD) assistive alternative, however, manual contralateral actuation occupies the sound hand (100% involvement during adjustment), precluding true bimanual independence.

Rodrigo Valdés-Cienfuegos, Pamela Torres-Rodríguez, José Antonio Rodríguez-Calderón et al. · 0 citations
Open access Oct 2026

Design and Bending Mechanism of Circumferentially Symmetric Four-Chamber Dual-Channel Soft Pneumatic Actuator

Soft pneumatic actuators (SPAs) are widely applied in soft robots for their good compliance and environmental adaptability. However, conventional SPAs with a single prescribed deformation mode provide limited dexterity for tasks requiring reconfigurable motion. To address this limitation, this paper proposes a four-cha...

Xu-Yang Shang, Yi-Qi Qin, Shu-Man Xu et al. · 0 citations

We use cookies to run the site and, with your consent, for analytics and to show ads. See our Cookie Policy.